About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

Choosing a supporting deck and underlay beneath a roof covering

The choice of substrate and underlay depends primarily on whether the roofing system requires full boarding or just a batten grid. This article gives you the criteria to assess whether a membrane is suitable for contact with insulation or a rigid substrate, how roof pitch affects requirements, and why ventilation and vapour control matter. Check how the selection of these elements affects the roof's ability to dry out and what consequences changing one of them has. Remember that design decisions remain with the designer.

By |2026-11-14T22:55:10+01:002024-02-27|Building guide|Comments Off on Choosing a supporting deck and underlay beneath a roof covering

A leaking roof: how to trace the cause and decide what to do next

First limit damage inside and have the roof inspected, rather than immediately looking for the culprit at the wet patch. Water may travel along the membrane or structure, and a hole visible above a stain is not always the source of the leak. It is worth establishing whether the problem occurs with every rain or only with rain from a particular wind direction, and distinguishing precipitation from water-vapour condensation. The check should cover valleys, chimney flashings, wall junctions and service penetrations. An effective repair removes the cause instead of covering an arbitrary section of the roof slope.

By |2026-11-14T16:07:59+01:002024-02-26|Building guide|Comments Off on A leaking roof: how to trace the cause and decide what to do next

Four checks when selecting a tile-effect metal roof covering

Begin by establishing whether the chosen roofing tile profile actually suits the roof geometry and the intended method of installation, rather than by comparing colours. Check its conformity with the design, the specification of the steel and workmanship, the suitability of the coating for the surrounding conditions, and the full cost of the finished roof including delivery. Any one of these points may rule out a seemingly attractive offer. Only once they have been set side by side is it worth deciding between similar variants, since the appearance of a sample alone will not reveal technical differences.

By |2026-11-15T03:01:32+01:002024-02-18|Building guide|Comments Off on Four checks when selecting a tile-effect metal roof covering

Building a watertight flat roof: design details and limitations

The watertightness of a flat roof depends above all on a coherent layer system, not on the covering material alone. Before construction, it is worth establishing how water will be drained, who will service the surface and how, and whether the roof is to serve additional functions. Falls, waterproofing, outlets and continuity of insulation form a whole in which every element must fit together. PIR boards can be part of such a system, but they do not replace a watertight covering. The project and the care taken over details determine success.

By |2026-11-14T22:54:04+01:002024-02-16|Building guide|Comments Off on Building a watertight flat roof: design details and limitations

When a cheaper roof covering raises the total cost

A lower price for the covering does not always mean a cheaper roof — what matters is whether the material meets the project requirements and suits the entire roof slope. Before comparing offers, check whether the running metres share the same basis of settlement, whether the product name confirms the parameters, and what the scope of accessories and labour includes. Saving makes sense when it reduces waste and unnecessary complications rather than omitting necessary layers. Compare the cost of the finished solution and its later maintenance, not just the price of a sheet.

By |2026-11-14T19:19:48+01:002024-02-12|Building guide|Comments Off on When a cheaper roof covering raises the total cost

Can a metal roof work on an energy-efficient home?

Metal sheeting suits an energy-efficient house only as part of a complete, well-considered roof assembly, not as a stand-alone solution. Before approving the design, it is worth checking the continuity of insulation, air tightness and how the eaves, ridge and service penetrations are detailed. Equally important are the declared lambda of the insulating material and the choice of counter-batten fixings capable of carrying the covering loads. Whether the roof meets its targets depends on how all layers work together with the rest of the building, so the thermal assessment should cover the whole assembly rather than a single sheet.

By |2026-11-14T16:08:03+01:002024-02-10|Building guide|Comments Off on Can a metal roof work on an energy-efficient home?

Coordinating metal fence pickets with the lines of the house façade

The fence and the façade are usually seen together. Their divisions can either give each other order or compete unnecessarily. Metal fence pickets create a regular, fine rhythm that is worth setting against the larger elements of the house. There is no need to align every picket with the window axis. What matters more is a clear relationship between the entrance, the posts and the infill. A well-composed front looks coherent even though it consists of elements of different scales and purposes. On the façade, we first notice the volume, the roof and the larger openings. The fence has its own large divisions: the gate, the pedestrian gate and the bays. Only within these does the rhythm of individual pickets appear. It is worth keeping this order when planning. Trying to match the width of every profile to the window detail can complicate the composition without any visible benefit.

By |2026-11-15T17:54:16+01:002024-02-05|Building guide|Comments Off on Coordinating metal fence pickets with the lines of the house façade

SOPREMA PIR boards: specifying product and system requirements

The specification for a BLUE A roof should link the list of materials with the details. If a different designation appears on the drawing than in the cost estimate, the discrepancy must be clarified before purchase. It is worth specifying the points at which the layers that will be covered are to be inspected and accepted. Such a record gives the contractor a verifiable requirement instead of a general note about airtightness. The EFYOS BLUE A specification should identify the function that the complete roof with vapour control layer, thermal insulation and covering is to perform. One element requiring an unambiguous description is the connection of the vapour control layer to the rooflight upstand. The input data should include the position of all layers at the base of the rooflight, not only the area intended for thermal insulation.

By |2026-11-16T00:52:48+01:002024-02-04|Building guide|Comments Off on SOPREMA PIR boards: specifying product and system requirements

Steel and glass solar roofing: differences in appearance

A steel roof with integrated cells and a roof based on glass modules can both combine the roof covering with energy production, but they look different and are built differently. In the first solution, the longitudinal rhythm of the panels and standing seams is what matters. In the second, the grid of modules and the way they are joined play a greater role. Both require a complete design. The choice should be based on the architecture of the house, the actual construction of the system and the expected degree of integration, not on colour alone. The cells are part of specific steel covering elements. Active panels can be combined with passive parts of the roof slope of matching character. The roof retains the pattern created by the longitudinal elements and standing seams.

By |2026-11-15T17:56:04+01:002024-02-01|Building guide|Comments Off on Steel and glass solar roofing: differences in appearance

Galvanised steel sections: durability starts with the connection details

The choice of coating is important, but it is not the end of the corrosion protection story. Durability is also determined by where the profile is built in, whether it can dry out, and how connections are made. Galvanised profiles can have a correct specification and still end up in unforeseen permanent dampness. The design should therefore cover the operating conditions of each characteristic detail. This applies both to a large purlin and to a small omega profile behind the cladding. It is necessary to establish what will actually happen in the building. Technological processes, humidity, the method of cleaning and ventilation all matter. A heated room is not always dry, and a sheltered zone does not always stay free of condensation. A general building name does not replace an assessment of the environment.

By |2026-11-15T17:50:36+01:002024-01-31|Building guide|Comments Off on Galvanised steel sections: durability starts with the connection details
Back to top