Two colours in a metal picket fence: when to keep the palette simple

Two colours can organise the zones of a property or introduce unnecessary chaos. In a fence made of pickets the effect is particularly clear, because each shade is repeated on many elements. Metal fence pickets offer various combination options, but the availability of specific coatings must be confirmed. It is worth starting with the question of what role the second colour is to play. If the answer comes down only to adding variety, it is also worth comparing a calmer variant with a single colour of infill. A fence can be two-colour without alternating different pickets. The second colour can appear on the posts, the frame or the plinth. Such a division corresponds to the construction of the fence and is often easy to read. It is worth considering it first. It allows a repeatable rhythm of the infill to be maintained while clearly showing the larger fields of the structure.

By |2026-11-15T17:54:52+01:002023-07-04|Building guide|Comments Off on Two colours in a metal picket fence: when to keep the palette simple

Ordering trapezoidal steel roofing: from roof measurements to sheet sizes

Begin by establishing what function the trapezoidal sheet is to serve: whether it will be external cladding, wall lining, or a load-bearing element of another system. This determines the choice of profile and documentation. Next, check whether the building is heated and where moisture may come from, and plan for rooftop equipment and point loads. Prepare a sketch with dimensions of the roof slopes, eaves, ridges and pitch. In an existing building, check the plane and condition of the supports. Remember that T18 and T35 designations do not define a single geometry – verify height, rib pitch and coverage width.

By |2026-11-14T16:06:27+01:002023-07-02|Building guide|Comments Off on Ordering trapezoidal steel roofing: from roof measurements to sheet sizes

How to choose a coating for tile-effect steel roofing

The choice of a metal roof tile depends on the entire coating system, not just colour or lacquer thickness. A building owner should check how the metallic protection, pre-treatment layers and organic coating work together in the specific environment. This article covers finish types, the influence of surroundings, the meaning of gloss and texture, and the real scope of a warranty. It also stresses that comparing offers requires identical sheet parameters and full technical data. The decision becomes informed when corrosion resistance, installation conditions and subsequent care are weighed together, rather than relying on a trade name.

By |2026-11-14T19:21:41+01:002023-06-17|Building guide|Comments Off on How to choose a coating for tile-effect steel roofing

BauderPIR M/MF: selecting properties from current documents

For M/MF, the lambda value must be assigned to a specific thickness. For example, 100 mm should be calculated using the applicable range, not the value for the aluminium-faced board. It is worth recording the mineral facing and the M or MF edge separately, so that a substitute product can be assessed against the full set of relevant characteristics. The BauderPIR M/MF specification should identify the function the roof with the mineral-faced PIR board is to fulfil. The area of the fleece under the waterproofing layer is an element that requires an unambiguous description. The input data should include the thickness of the insulation ordered and the condition of the substrate under the covering, not only the area to be insulated. The coordinating document remains the set of documents for the specific M or MF thickness and the connection to the covering.

By |2026-11-16T00:53:03+01:002023-06-15|Building guide|Comments Off on BauderPIR M/MF: selecting properties from current documents

Cleaning and maintaining a complete set of metal flashings

Flashings do not require daily attention, but they should remain part of building inspections. Water, dust and installation damage affect their condition. For maintenance, it is best to start by identifying the material and the location of the soiling. Only then should cleaning or repair be selected. A single random product is not the solution for all surfaces and all details. The material specification is useful for care. Galvanised, aluzinc and coated steel sheets have different surface finishes. A coloured element may also belong to one of several coating variants. It is worth locating the delivery documents before choosing a product for a stubborn stain.

By |2026-11-15T03:03:55+01:002023-06-12|Building guide|Comments Off on Cleaning and maintaining a complete set of metal flashings

Roof insulation: which decisions come before installation?

First establish where the boundary of the heated part of the building should run, and only then choose the material. This guide sets out the sequence of decisions: insulating the roof slope or the ceiling, calculating thickness rather than guessing, a between-rafter or above-rafter layout, and protection against moisture. It also covers substrate preparation, fixings and details at the eaves, wall plate and service penetrations. Each of these choices involves different trade-offs, so leave design decisions to the designer and, before buying material, review the continuity of the insulation and the airtightness of the joints.

By |2026-11-14T19:21:17+01:002023-06-05|Building guide|Comments Off on Roof insulation: which decisions come before installation?

Laying tile-effect metal roofing sheets cut to length

The key decision for cut-to-size metal roofing tiles is whether the order dimensions come from an actual measurement of the roof slopes rather than the house outline alone. Readers should check the lengths, widths and diagonals, the positions of valleys, chimneys and roof windows, and how the covering length depends on eaves and ridge details. A project drawing may not be enough. These findings tie into the choice of profile and the product instructions, so design decisions are left to the designer.

By |2026-11-14T22:54:27+01:002023-05-30|Building guide|Comments Off on Laying tile-effect metal roofing sheets cut to length

Documenting termPIR WS: lambda and system requirements

The termPIR WS specification should describe more than the PIR core. Lambda changes with thickness, and the facing has a specific structure. Without this information, substituting the product may retain the material name but change characteristics that are important for the entire roof. termPIR WS consists of a PIR core and a double-sided vapour-permeable glass fleece facing. This is a different surface from a vapour-tight aluminium laminate. In the specification for the application described as PIR boards, clearly indicate the flat roof surface on which the board facing is to work together with the covering. The termPIR WS fleece must be linked to the layers and the fixing method of the adopted roof covering, and the adopted variant must be clearly marked in the documentation.

By |2026-11-16T00:51:56+01:002023-05-28|Building guide|Comments Off on Documenting termPIR WS: lambda and system requirements

How should you cut insulated panels without damaging the facings?

Insulated panels are cut with tools suited to the metal facings and the core. Edge heating must be limited, the component well supported and swarf removed quickly. An angle grinder with a grinding disc is not the right choice for this task. Before cutting, check the instructions for the chosen system and the finishing detail. A clean cut alone is not enough if the core is left exposed or the sheet's protection is damaged after the work. The facing is thin sheet protected against corrosion. High temperature and sparks can damage its protective layers. Metal particles left on the surface begin to corrode and leave marks on the paint. They are not always visible immediately after the work is finished.

By |2026-11-14T09:56:13+01:002023-05-28|Building guide|Comments Off on How should you cut insulated panels without damaging the facings?

How long does an insulated panel with mineral wool last and what shortens its service life?

The durability of an insulated panel with mineral wool is determined by the entire element. The facings, their protection, the bond with the core and the tightness of the joints all matter. There is no single number of years that applies to every hall. A dry warehouse performs differently from a building with high humidity or an aggressive atmosphere. Good choice of coating and regular inspections help avoid repairs that seemingly start from a minor scratch. Mineral wool is an important part of the panel, but the enclosure does not consist of insulation alone. Thin facings and the core work together to carry loads. Loss of adhesion, severe denting or corrosion of the sheet can impair the element's performance even when the insulating material is still in place.

By |2026-11-14T09:54:22+01:002023-05-24|Building guide|Comments Off on How long does an insulated panel with mineral wool last and what shortens its service life?
Back to top