What determines rafter size and spacing on a roof?

The cross-section and spacing of rafters are determined by structural calculations, not just the type of roofing. To select the right dimensions, check the rafter length between supports, roof pitch, building location, height and surroundings, as well as the planned roofing, insulation and attic build-up. It is also essential to establish the structural scheme, i.e. the support conditions and connections to the truss. These data must be passed to the designer, who will verify load capacity and deflection; ready-made tables can only serve as a guide.

By |2026-11-14T16:06:55+01:002024-11-21|Building guide|Comments Off on What determines rafter size and spacing on a roof?

Where cold-formed sections carry loads between the frame and the cladding

In a steel hall, not every element performs the same function. Main frames, purlins, rails and lattice girders form successive parts of the system. Cold-formed profiles may appear in several of them, but each time the load path must be defined. This helps to select the section correctly and to establish responsibility for the details. Z-sections, C-sections, sigmas and omegas are not simply different ways of filling the space between columns. Wind acting on the wall panel reaches its supports through the fasteners. The forces then pass through the rails or other elements to the main structure. On the roof, purlins perform a similar role. The entire chain must be verified, including the connections. Correct selection of one segment does not yet confirm the safety of the complete load path.

By |2026-11-15T03:03:19+01:002024-11-15|Building guide|Comments Off on Where cold-formed sections carry loads between the frame and the cladding

What are the advantages of steel exterior window sills?

A steel external window sill primarily drains water from beneath the window and protects the façade, so when choosing one it is worth looking not only at colour but at the fall, drip edge and connection to the window. Coated sheet metal offers wide scope to match gutters, roof or joinery, and its low weight makes transport and work easier. Compare physical samples under the same lighting before ordering. Differences in gloss and texture can be hard to see on a screen.

By |2026-11-14T19:20:34+01:002024-11-14|Building guide|Comments Off on What are the advantages of steel exterior window sills?

Five roofing defects to look for before accepting the work

Before accepting a metal roof, it is worth checking not only the colour of the covering but above all the quality of the substrate, the direction of the laps, the choice of fasteners, the condition of the coating and the patency of ventilation and drainage. These five areas help catch errors that remain invisible from street level. The building owner should plan a stage-by-stage inspection and agree with the contractor when to review the battens, the underlay and the key flashings. What matters is documenting the places later covered, so the assessment does not rely solely on a general view.

By |2026-11-14T22:55:08+01:002024-11-13|Building guide|Comments Off on Five roofing defects to look for before accepting the work

Metal roof installation costs: how to compare labour quotes

To compare roofing labour, first establish whether the rate refers to roof area rather than the home's usable floor area, and ask for the work to be broken down into covering, battens and flashings. Send every contractor the same scope: plan, sections, roof dimensions, covering type, number of chimneys and windows, and access for installation. Check how openings, valleys and eaves are settled, because a price per metre without a description can mislead. For renovation, add dismantling and waste disposal. Compare net or gross offers against one shared list of tasks.

By |2026-11-14T16:08:48+01:002024-11-12|Building guide|Comments Off on Metal roof installation costs: how to compare labour quotes

How do you match the thickness of an insulated panel to the building’s requirements?

The thickness of an insulated panel is selected to suit thermal performance, loads and building requirements at the same time. The information 'heated hall' alone is not enough. You need the core type, the support arrangement, the facings, the operating conditions and the fire requirements. A thicker panel can improve insulation, but it does not solve every problem. The selection should be based on the documentation for the specific product and the entire building envelope. Define the function of the rooms and the operating temperature. Note whether the building will be heated continuously, periodically or not at all. In a cold store the conditions are different from those in a workshop or a warehouse for dry materials. Humidity and the environment on both sides of the panel also matter. Then separate the walls and the roof.

By |2026-11-14T12:15:50+01:002024-11-11|Building guide|Comments Off on How do you match the thickness of an insulated panel to the building’s requirements?

Can T18 profiled steel sheet be used as an eaves soffit?

T18 trapezoidal sheet may work as a soffit finish, but only after checking that the profile, supports and coating suit this use. Above all, assess the direction in which the trapezoid runs, how the sheet is fixed to the substructure, and whether the roof layout requires an air inlet that must be kept open. A sample mounted in the intended direction also shows whether the rib pattern will look too strong across a narrow strip. Decide on the material together with the gutter, flashings and under-sheet layers, because appearance must work with ventilation and drainage.

By |2026-11-14T22:53:18+01:002024-11-10|Building guide|Comments Off on Can T18 profiled steel sheet be used as an eaves soffit?

Winter roof preparation and what to do when snow builds up

Before winter, decide who will assess the roof after heavy snowfall and by what criteria. Measuring snow depth alone is not enough, because weight, distribution and the load capacity of the structure all matter. The building owner should also check that drainage is clear, that snow guards are sound and that any elements which have already worked loose are inspected. Repairs must suit the type of covering and the conditions in which materials are applied, and checks should be planned well ahead so that parts can be ordered. Below we discuss these choices and the trade-offs involved.

By |2026-11-15T03:01:59+01:002024-11-07|Building guide|Comments Off on Winter roof preparation and what to do when snow builds up

Protecting starter profiles and the base of the cladding from moisture

The lower part of the wall operates under different conditions than its upper sections. Splash water, dirt and moisture from the immediate surroundings reach it. Starter profiles and plinth flashings must be selected with this zone in mind. Using galvanised steel sheet alone does not solve all the problems. The position of the components, the seals and the absence of places where water unintentionally accumulates are also important. Before choosing the material, it is worth examining the surroundings of the wall. Ground surfacing, drainage and the way the building is used can all matter. Different dirt occurs on a quiet façade, different dirt at an intensively used gate. Not every situation should be reduced to the same sheet metal designation.

By |2026-11-15T03:03:34+01:002024-11-02|Building guide|Comments Off on Protecting starter profiles and the base of the cladding from moisture

The top line of a metal picket fence: straight, curved or stepped?

The appearance of the top edge of a fence comes down to two decisions. The first concerns how an individual picket is finished. The second concerns the length and position of all the elements within a bay. Rounded ends do not automatically mean the whole fence is arched. Metal pickets of equal length can have level tops even if each end has a gentle curve. It is worth separating these two questions before ordering. Make two sketches of the same bay, changing only one element. First compare the ends at equal height, then check how the outline changes. That way you will see more easily which decision really gives the fence the character you want. This makes it easier to achieve the intended effect and prevents mistakes during production.

By |2026-11-15T17:54:48+01:002024-10-23|Building guide|Comments Off on The top line of a metal picket fence: straight, curved or stepped?
Back to top