Which roof coverings put the least weight on the structure?

The covering that places the least load on the structure is the one with the lowest mass per square metre of finished roof surface, not per individual sheet. When choosing, check whether the stated value refers to the covering area and what purlins and additional layers are required. It is also necessary to establish where these loads act and how they reach the walls. A comparison made for the same roof area avoids a misleading impression of lightness. Final design decisions remain with the structural designer.

By |2026-11-14T22:54:22+01:002024-10-22|Building guide|Comments Off on Which roof coverings put the least weight on the structure?

Metal fence pickets: how they work and when to choose them

Metal fence pickets are profiled infill elements for fence bays, available in various widths and profile depths. Before buying, check whether the chosen profile suits the existing structure and the desired gap, not just the façade colour. By examining a real sample, you can assess the surface on the street and garden sides and the finish of the edges. Bear in mind that a similar front appearance does not guarantee identical installation requirements. The decision on a double-sided layout or denser spacing should account for wind loads and fixing to the rails.

By |2026-11-14T19:22:27+01:002024-10-19|Building guide|Comments Off on Metal fence pickets: how they work and when to choose them

Choosing wall sandwich panels for the façade finish you want

First decide whether the panel is also to serve as the finished surface on the inside, as this determines the choice of both faces. Then check whether the chosen surface profile and panel layout suit the building's form, and whether visible or concealed fixing matches the intended facade rhythm. Compare PIR and mineral wool cores for insulation, reaction to fire and acoustics, bearing in mind that the parameters relate to a specific product and the whole assembly. A dark colour may require a different colour group and affect span. Include trims, corners and seals in the quotation.

By |2026-11-14T22:52:06+01:002024-10-13|Building guide|Comments Off on Choosing wall sandwich panels for the façade finish you want

What distinguishes a roof sandwich panel from a wall panel?

Roof and façade sandwich panels are not interchangeable, as they differ in purpose, profile, joint and fixing. When choosing, check above all the product data sheet, the cross-section drawing and the installation instructions for the specific application. The roof must carry the design loads and drain water, while the façade must perform under wind action and have sealed joints. The appearance of the sheet alone does not determine the application – the product designation and the scope given in the documentation do. Compare parameters only for the correct function, because a similar core and nominal thickness do not guarantee the same properties.

By |2026-11-14T16:06:34+01:002024-10-07|Building guide|Comments Off on What distinguishes a roof sandwich panel from a wall panel?

Planning the anchors between a timber wall plate and a concrete ring beam

The key decision when anchoring the wall plate to the ring beam is matching the anchor type, spacing and embedment geometry to the specific loads, concrete class and rafter layout. It is worth checking whether the design clearly specifies these parameters and how forces are transferred through washers and nuts before concreting begins. Also verify that the solution accounts for wind action and that connection details at ends and corners are consistent with the rest of the roof structure. Without this, the risk of clashes and installation errors increases considerably.

By |2026-11-14T22:52:57+01:002024-10-04|Building guide|Comments Off on Planning the anchors between a timber wall plate and a concrete ring beam

Sigma section load capacity: why catalogue dimensions are not a structural calculation

A profile catalogue may list mass, cross-sectional area and moments of inertia. This is valuable information, but it is not the complete answer to the question of load-bearing capacity in a specific hall. Sigma profiles belong to the group of thin-walled sections. Their webs and bends interact under specific conditions. To select an element, geometric data must be combined with loads, support conditions and material properties. Gross values refer to the geometry of the entire cross-section. They help compare the distribution of material and prepare a model. However, they do not automatically account for all phenomena that limit load-bearing capacity. Therefore, they should not be converted into the permissible load of any beam without further assumptions.

By |2026-11-15T17:50:32+01:002024-10-03|Building guide|Comments Off on Sigma section load capacity: why catalogue dimensions are not a structural calculation

Collar beam roofs: how they work, their advantages and their limits

A collar-tie roof works when the design specifies horizontal members connecting the rafters at a set height, not when you are looking for a universal solution without supports. Before deciding, compare the position and cross-section of the collar ties and the type of connections with the documentation, as these parameters determine the usable potential of the attic. Also check the complete layer build-up, how the insulation runs, and any changes made on site. The designer selects the arrangement for the loads and geometry, so a similar footprint does not guarantee the same solutions.

By |2026-11-14T22:53:38+01:002024-10-01|Building guide|Comments Off on Collar beam roofs: how they work, their advantages and their limits

How do I order cut-to-size tile-effect metal roofing without mistakes?

Ordering cut-to-size tile-effect metal roofing should start with a verified measurement and a layout plan for the sheets. The roof area alone is not enough. You need to specify the profile, coating, thickness, colour and lengths with quantities. Flashings and delivery conditions are also required. The sheet length must take into account the pattern module and the details at the eaves and ridge. It is at this stage that costly mistakes and an excessive number of offcuts can be avoided. Prepare a plan of all roof slopes. Mark the lengths of eaves, ridges, roof valleys and corners. Specify the pitch and the position of chimneys, windows and penetrations. Dimensions should refer to the actual roof or the approved design. A sketch of the house's external walls does not determine the covering lengths because it does not show overhangs and diagonal dimensions.

By |2026-11-14T09:54:04+01:002024-09-28|Building guide|Comments Off on How do I order cut-to-size tile-effect metal roofing without mistakes?

Specifying trapezoidal steel sheets for a façade

The choice of trapezoidal sheet for a façade depends above all on how the building should look from a distance and up close, not on the profile name alone. Check the profile drawing, the effective width and the direction in which the sheets are laid, as these affect the rhythm of the wall and how openings are resolved. Compare the support and environmental requirements with the substructure design. Look at a sample and plan the sheet layout across the whole façade to avoid accidental narrow strips at the corners.

By |2026-11-14T19:20:56+01:002024-09-28|Building guide|Comments Off on Specifying trapezoidal steel sheets for a façade

Retrofitting insulation to a steel building: what to check before buying panels

An older steel hall can serve well as seasonal storage and, after a change of use, may require heating. That is when the idea of replacing the envelope or adding insulation arises. Buying panels should, however, be one of the later steps. First, the condition of the building must be assessed and the conditions it is to provide after modernisation established. Drawings, information on materials and a history of changes are needed. If the documentation is incomplete, a survey of the existing elements may be necessary. In a steel hall, the condition of the frames, bracing, connections and envelope supports is checked. Corrosion, deformation or damage require assessment before loads are increased.

By |2026-11-15T03:03:02+01:002024-09-25|Building guide|Comments Off on Retrofitting insulation to a steel building: what to check before buying panels
Back to top