About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

Using a heat balance to estimate heating requirements for a steel building

The question about heating often arises only once the building dimensions have already been fixed. Yet a steel hall may need a completely different system after changes to the doors, temperature or mode of operation. The unit's output should not be derived from floor area alone. First you need to establish where heat escapes and where it comes in. Heating output describes the ability to supply heat at a given moment. Annual consumption also depends on operating time, weather and settings. Two steel halls of the same area may have a similar design output but different bills. One operates daily, the other maintains a higher temperature only for part of the week.

By |2026-11-15T03:02:37+01:002025-08-20|Building guide|Comments Off on Using a heat balance to estimate heating requirements for a steel building

Choosing a covering for a mansard roof

The choice of roofing for a mansard roof should be based on the roof drawing, not on a single averaged slope. Check whether the product is approved for both pitches and how the break, dormers and continuity of the layers under the covering are resolved. Cut-to-length and modular metal tiles differ in cutting layout, number of joints and ease of installation, so compare them using the dimensions of both parts. Cost the covering, flashings and access separately, and leave structural and insulation decisions to the designer.

By |2026-11-14T19:22:05+01:002025-08-15|Building guide|Comments Off on Choosing a covering for a mansard roof

Is it worth ordering trapezoidal steel sheet with an anti-condensation layer?

An anti-condensation layer on the underside of the sheet can reduce dripping of water formed by condensing vapour. It acts as a temporary store of moisture that must subsequently dry out. It is most often considered in adequately ventilated buildings with an uninsulated covering. It does not replace thermal insulation, a vapour barrier or repair of a leaking roof. Whether it makes sense to buy depends on the conditions inside the building and the possibility of removing moisture. The roof surface can cool to a temperature at which the vapour contained in the air begins to condense. Droplets then appear from below, even though no rain has passed through the covering. The phenomenon depends on surface temperature and air humidity. It may be noticeable after a cool night or with a large difference in conditions between the interior and the surroundings.

By |2026-11-14T12:17:02+01:002025-08-13|Building guide|Comments Off on Is it worth ordering trapezoidal steel sheet with an anti-condensation layer?

Fibre cement roofing and summer heat inside the building

On a hot day, room temperature is determined by more than the type of outer sheet. Sun, insulation, windows, air exchange and how the building is used all matter. Fibre cement sheets can be part of a well-designed envelope, but they do not guarantee lower temperatures. Asbestos-free fibre cement also heats up in the sun. A sensible choice of roofing requires looking at the path of heat through the whole roof and the other parts of the building. Radiation falls on the roof, and some of the energy is absorbed by the material. The amount depends among other things on the properties of the surface, the angle of incidence and the ambient conditions. A dark colour is often associated with greater absorption of radiation than a light one, but it does not replace data for a specific coating.

By |2026-11-15T17:56:21+01:002025-08-10|Building guide|Comments Off on Fibre cement roofing and summer heat inside the building

Planning a roof replacement from survey to installation

Before ordering materials, decide whether you are replacing only the covering or rebuilding the entire roof assembly – this choice defines the scope and schedule. Check the condition of the trusses, flashings and drainage, and inspect the roof from inside as well; signs of damp or deflected timber help separate a simple sheet replacement from a wider upgrade. If the structure is in doubt, arrange an assessment by a suitably qualified person before delivery. Also plan how to protect the building during dismantling and how unforeseen repairs will be settled.

By |2026-11-14T19:21:16+01:002025-08-10|Building guide|Comments Off on Planning a roof replacement from survey to installation

Light and shade on metal fence pickets throughout the day

Metal fence pickets do not have a single unchanging appearance. In the morning their pressings may stand out clearly, while under an overcast sky they look much calmer. The angle of the light, the surroundings and the viewing position all change. A matt coating reacts differently from a glossy one. It is worth taking this variability into account when choosing a fence. A sample placed only briefly in deep shade may conceal features that will appear on an open frontage. There is no need to choose the material afresh, but it is good to see it in more than one position. This way the difference between a sample in the shop and the view on the property will not come as a surprise. Assessing the material should cover several ordinary conditions in which it will be viewed.

By |2026-11-15T17:55:05+01:002025-08-09|Building guide|Comments Off on Light and shade on metal fence pickets throughout the day

Which trapezoidal steel profile suits a canopy roof?

Choosing trapezoidal sheet for a carport roof requires first checking the purlin spacing, expected loads and roof pitch – only then can T18 or T35 be considered. It is worth establishing whether the structure already exists or is still being designed, and what forces will act on the open carport, including from underneath. Condensation dripping beneath the sheet must be resolved separately. The final decision rests with the designer, who will select the profile based on the manufacturer's tables and local conditions.

By |2026-11-14T16:09:03+01:002025-08-07|Building guide|Comments Off on Which trapezoidal steel profile suits a canopy roof?

How eaves details shape the appearance of an integrated PV roof

The eave marks the lower edge of the roof and strongly influences how the whole building is perceived. With integrated photovoltaics, it should be planned as carefully as the active roof surface. It must drain water, work together with ventilation and match the geometry of the covering. A well-resolved detail reinforces the advantage of BIPV, namely a compact form without a separate mounting structure for the panels. The aim is not to conceal it as much as possible, but to achieve a clear combination of function and appearance. It is the boundary between the roof and the façade. Looking at the house from ground level, we often see it more clearly than the middle section of the roof slope. An uneven line, a random height of the flashing or a poorly fitted gutter can weaken the effect even of very carefully laid panels.

By |2026-11-15T17:55:30+01:002025-08-06|Building guide|Comments Off on How eaves details shape the appearance of an integrated PV roof

Light or dark fibre cement roofing? Why colour matters

The roof colour is usually chosen from a photo of the house or to match the façade. That is a good starting point, but it is also worth checking the sunlight conditions and the later maintenance. Fibre cement sheets can have a natural grey tone or a factory-applied coating in specific colours. Asbestos-free fibre cement in a light and a dark variant does not have to behave identically in the sun. However, no colour replaces proper insulation or ventilation of the entire roof. A small fragment under a shop lamp may look different from a large roof surface in daylight. It is worth assessing a sample in the morning, in the afternoon and in the shade. The neighbouring walls, timber, trees and other roofs matter.

By |2026-11-16T00:50:07+01:002025-07-31|Building guide|Comments Off on Light or dark fibre cement roofing? Why colour matters

IKO enertherm KR ALU: input data for floor design

A floor design with KR ALU should state the PIR thickness, the screed requirements and the heating design separately. The mesh printed on the facing is not a basis for dimensioning the installation. Likewise, CS does not replace the assessment of deformation of the entire cross-section. A single layer schedule should combine these separate data at a common finished-floor level. The IKO enertherm KR ALU specification should identify the function that the floor assembly with insulation beneath the heating and screed is to perform. Elements requiring an unambiguous description are the threshold between rooms and the passage of services. The input data should include the height from the substrate to the finished floor, not only the area intended for thermal insulation.

By |2026-11-16T00:53:22+01:002025-07-31|Building guide|Comments Off on IKO enertherm KR ALU: input data for floor design
Back to top