About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

Aligning photovoltaic roof sections with roof windows

Window positions and photovoltaic roof layouts should be considered together. This allows the roof slope to look calm while the interior retains the necessary light and comfort. Steel BIPV makes it possible to combine active fields with passive zones at the openings. This does not mean every window must be subordinated to the modules. A good design seeks harmony between the function of the house, the actual system formats and a clear roof pattern. First, the needs of the rooms and the possible roof geometry must be known. Windows serve the occupants, so their position should not result solely from the wish to add another panel. At the same time, it is worth checking BIPV formats early. This avoids a situation where a fixed opening layout leaves difficult, random fragments of the roof slope.

By |2026-11-15T17:55:41+01:002025-12-24|Building guide|Comments Off on Aligning photovoltaic roof sections with roof windows

Five advantages of sheet metal as façade cladding

Sheet metal on a façade offers five benefits, but not every one applies to the same product. First establish whether you are comparing thin trapezoidal sheet, which is only an external cladding, or a sandwich wall panel with an insulating core. Check how the design and quotation cover the substructure, fixings, substrate, flashings and water drainage. Match the T18 or T35 profile to the building rather than to randomly chosen materials. A choice combining appearance, load capacity, thermal requirements and maintenance will let you relate these benefits to a specific building.

By |2026-11-14T19:21:49+01:002025-12-24|Building guide|Comments Off on Five advantages of sheet metal as façade cladding

Fixing sandwich panels to a masonry wall

Insulated wall panels on a masonry wall usually require a designed method of support and fixing. They should not be screwed into random locations in the masonry, nor should it be assumed that any façade plug will be suitable. The condition of the substrate, the loads, the geometry and the moisture conditions must be assessed. Only then are the subframe, anchors and panels selected. The method of execution depends on whether a new cladding or the insulation of an existing wall is being created. Establish the wall material, its thickness and its technical condition. Concrete behaves differently from solid brick, and solid brick differently from hollow block. Old render is not proof of the load-bearing capacity of the substrate. Cracks, dampness and loose fragments must be identified.

By |2026-11-14T12:16:11+01:002025-12-23|Building guide|Comments Off on Fixing sandwich panels to a masonry wall

How to choose PIR insulation for a ceramic block wall?

PIR insulation for a ceramic block wall is selected according to the parameters of the entire wall, not just the material name. PIR can reduce the insulation thickness and make it easier to detail around windows or a narrow eaves. However, a board suitable for external walls must be chosen. A standard aluminium facing does not mean that adhesive, mesh and render can be applied directly to the product. Ceramic blocks vary in thickness, void layout and thermal properties. The mortar and the way joints are executed also matter. A wall made of blocks filled with insulation behaves differently from an older wall made of blocks without such filling. Measuring the wall width alone is not enough for an accurate selection.

By |2026-11-14T09:55:38+01:002025-12-20|Building guide|Comments Off on How to choose PIR insulation for a ceramic block wall?

Trapezoidal cladding sheets and structural decking: what is the difference?

What matters is whether the trapezoidal sheet merely encloses the building or also carries loads within the roof structure. In the first case, check above all wind action and the permissible deflection; in the second, check selection for loads in accordance with the design. Profile height alone does not determine suitability; steel grade and thickness, the support scheme and the connections all count. Review the load table for the relevant scheme and conditions, and also consider openings, insulation and surface protection. Leave final design decisions to the designer.

By |2026-11-14T22:55:29+01:002025-12-17|Building guide|Comments Off on Trapezoidal cladding sheets and structural decking: what is the difference?

Choosing a flat roof covering and the layers beneath it

A flat roof needs a considered layer build-up, not just a single decision about the covering. The building owner and the trade should check whether the structural base, moisture control, thermal insulation and waterproofing form a coherent system, and whether the roof plan shows outlets and high points. The choice of PIR variant depends on the declared lambda and its compatibility with the membrane, not on the material name alone. The fall and its execution must suit the chosen system, so the drainage plan is developed together with the cross-section.

By |2026-11-14T19:18:42+01:002025-12-15|Building guide|Comments Off on Choosing a flat roof covering and the layers beneath it

How can you reduce the cost of buying insulated panels without losing the required parameters?

The cost of insulated panels can be reduced through good cutting optimisation, a consistent order and matching the parameters to the project. Too thin a core, a random coating or missing installation parts only give apparent savings. First establish the wall and roof requirements. Then compare complete quotes for the same quantity of material. Also count the waste, delivery, unloading and work on site. In the enquiry, specify the intended use of the panel, the type of core, the thickness and the required thermal transmittance. State the conditions on both sides of the enclosure. A wall of an unheated warehouse has a different task from the enclosure of a room with a wet process. The fire, acoustic and structural requirements follow from the design.

By |2026-11-14T12:16:42+01:002025-12-15|Building guide|Comments Off on How can you reduce the cost of buying insulated panels without losing the required parameters?

Tile-effect metal roofing or trapezoidal T18 or T35? What to choose for a house roof

Tile-effect metal roofing, T18 and T35 can be used on house roofs if they suit the design and installation conditions. They differ in appearance, geometry and method of cutting. A higher profile alone does not mean a better roof. The choice should be determined by roof pitch, support, full cost and aesthetic expectations. The comfort of the attic, however, depends on the entire layer system, not just the shape of the outer sheet. Tile-effect metal roofing has transverse ribs that divide the surface into rows resembling roof tiles. Trapezoidal steel sheet forms a simpler pattern of long, parallel ribs. T18 gives a finer pattern than T35. The profile height affects the shadow, so the same colour may look different on each of these coverings.

By |2026-11-14T09:53:47+01:002025-12-12|Building guide|Comments Off on Tile-effect metal roofing or trapezoidal T18 or T35? What to choose for a house roof

How to choose the thickness of an insulated roof panel for a garage?

The garage roof is selected according to heating, moisture and loads. There is no single panel thickness suitable for every building. An unheated garage, a workshop and a room connected to the house place different demands. In addition to thermal insulation, supports, slope, seals and ventilation are important. A thinner panel may be sufficient in one project and unsuitable in another. This is the first question before choosing a thickness. In a continuously heated garage, limiting heat loss matters. In an unheated one, insulation slows temperature changes but does not by itself ensure a positive temperature throughout the winter. The required effect should be described without assuming that the material will replace a heat source.

By |2026-11-14T12:17:59+01:002025-12-12|Building guide|Comments Off on How to choose the thickness of an insulated roof panel for a garage?

How do you choose the length of insulated panels for the building and transport?

The length of an insulated panel is matched to the building geometry, the supports and the delivery options. The longest available panel does not always reduce the cost. It may require a different vehicle, unloading equipment and a different lifting method. Dividing it into shorter elements, in turn, creates additional joints. A good length schedule is based on verified dimensions, details and the documentation for the selected system. Panels are often made to the length specified in the order, but within the limits for the given product. For example, a PIR roof panel has a range of 2 to 16 m in its data sheet. The maximum depends on the colour and thickness. This is not a promise that every 16 m panel can be used in any layout.

By |2026-11-14T12:17:22+01:002025-12-02|Building guide|Comments Off on How do you choose the length of insulated panels for the building and transport?
Back to top