About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

Planning a fence with metal pickets

A boundary fence can have open spaces between its pickets. Screening a garden from view calls for a closer arrangement, which also affects the supports. Check how the fence looks both from the side and straight on, ideally using a sample panel, and plan the panels, gate and side entrance together with the slope of the ground. A denser infill reduces visibility but increases wind load, so leave the choice of posts and rails to the designer.

By |2026-11-14T19:20:58+01:002026-01-31|Building guide|Comments Off on Planning a fence with metal pickets

IKO enertherm ALU TAP: specifying falls and tapered board thicknesses

The ALU TAP documentation should assign each slope to a marked field. If the outlet is changed, both the drawing and the parts list must be updated. It is also worth defining how the levels are to be checked and accepted before waterproofing. Merely confirming that the PIR tapered board has been delivered does not prove that the layout is correct. The IKO enertherm ALU TAP specification should identify the function that a roof with aluminium-faced tapered boards of different slopes is to perform. One element requiring an unambiguous description is the junction between fields with a different drainage direction. The input data should include the height difference between the ends of the taper and the length in the direction of fall, not only the area to be insulated.

By |2026-11-16T00:53:23+01:002026-01-29|Building guide|Comments Off on IKO enertherm ALU TAP: specifying falls and tapered board thicknesses

Snow stops or snow fences to keep snow from sliding off a roof?

The choice between point snow guards and snow fences depends above all on what is to be retained and where. Rather than being guided by price, you need to establish the system's function, its permitted application and how the load is transferred to the roof. It is worth checking whether the solution matches the roof geometry, the covering type and the places at risk below the eaves. Location, pitch and roof length should also be taken into account. The designer should verify how the covering, brackets and fixings work together, since retaining snow alone does not increase the structure's load-bearing capacity.

By |2026-11-15T03:01:55+01:002026-01-29|Building guide|Comments Off on Snow stops or snow fences to keep snow from sliding off a roof?

How can you insulate a wall at the plot boundary when there is not enough space on the façade?

With a wall standing close to the plot boundary, every centimetre counts. Thinner PIR insulation can make a solution easier, but it does not remove the constraints linked to the building's position. If external insulation is not possible, the internal option must be assessed. It requires checking moisture, thermal bridges and fire protection. It is not enough to choose the thinnest board from the catalogue. An accurate measurement is more important than an estimate from the façade plan. You need to know the wall's position, its unevenness and the locations of protruding elements. Adhesive, finishing layers and any substructure are added to the insulation thickness. A 100 mm board does not mean that the finished façade will increase the building's dimension by exactly 100 mm.

By |2026-11-14T09:55:41+01:002026-01-27|Building guide|Comments Off on How can you insulate a wall at the plot boundary when there is not enough space on the façade?

Choosing roofing membranes for each layer in the roof

The choice of roofing membrane is determined above all by its position and role within the layer build-up, not by the weight of the roll alone. First establish whether you need an underlay membrane, a vapour barrier or both, then check how they fit the roof design. Take into account the substrate, permitted contact with thermal insulation, exposure time and how laps and junctions at walls, chimneys and services are sealed. Compare the declared properties and intended use of the product, since the term roofing membrane covers materials with different functions.

By |2026-11-15T03:01:16+01:002026-01-24|Building guide|Comments Off on Choosing roofing membranes for each layer in the roof

How do you choose insulated panels for cold rooms and freezers?

Insulated panels for cold rooms and freezers are selected according to the operating temperature, the ambient conditions and the overall heat balance. Choosing a large thickness alone will not ensure a tight chamber. The joints, seals, doors, floor and service penetrations all matter. PIR is useful thanks to its good insulation performance at a small thickness. However, a solution intended for refrigerated conditions must be used. An insulated panel consists of metal facings and a bonded core. In the refrigerated variant, the edge connection is particularly important. Suitable joint geometry and the specified seal limit the flow of air and vapour. This is not merely a thicker version of any façade panel.

By |2026-11-14T12:15:04+01:002026-01-23|Building guide|Comments Off on How do you choose insulated panels for cold rooms and freezers?

How to assess customer reviews of a sandwich panel and sheet metal supplier

Reviews of a supplier help assess service, but do not in themselves confirm the parameters of panels and sheets. The most informative are specific descriptions of the order, delivery and how a problem was resolved. Compare them with the material documentation and the written quote. Do not treat the star rating as a substitute for the specification. Before purchase, also check whether the review concerns a product and service similar to those you need. A customer account can show how the supplier responds to questions, confirms dimensions and organises transport. Information about order completeness, delivery time and contact after receipt is useful. A description of a clear course of events is particularly valuable. A score alone does not say what exactly was ordered.

By |2026-11-14T12:16:49+01:002026-01-16|Building guide|Comments Off on How to assess customer reviews of a sandwich panel and sheet metal supplier

How a mono-pitch roof is built and when to choose it

A mono-pitch roof is worth considering when a simple form and a single direction of water runoff matter more than freedom in shaping the cross-section. Above all, the reader should check whether the chosen covering and its minimum pitch suit the planned slope and whether drainage from the low edge has been thought through. Supports at different heights and the treatment of the high edge are equally important. The article helps compare these dependencies without imposing a ready-made solution.

By |2026-11-14T19:22:19+01:002026-01-16|Building guide|Comments Off on How a mono-pitch roof is built and when to choose it

Which metal roof coverings suit a modern building?

The modern character of a metal roof covering depends above all on how well it suits the building's form and function, not on the product name alone. Before choosing a profile, check whether the roof is to be the main element of the composition or will remain hidden behind a parapet, and consider the height of the slope and the role of the eaves. On large surfaces, the rhythm of the profiling, sheet lengths and joint layout matter; on a low building, the façade and detailing may count for more. Compare blachodachówka and sandwich panel options for proportion, slope and support so that the visualisation matches the real roof.

By |2026-11-14T19:19:53+01:002026-01-06|Building guide|Comments Off on Which metal roof coverings suit a modern building?

Roof coverings and the buildings they suit

The type of roof covering should be chosen above all to suit the roof pitch, the building structure and the function of the rooms beneath the roof, not merely the appearance of the surface. It is therefore worth first establishing whether an overlapping covering or a continuous waterproof layer is needed, and distinguishing a thin sheet of metal from a sandwich panel or PIR insulation. Check what pitch and support the system requires and whether the chosen material is permitted in that particular assembly.

By |2026-11-14T19:20:38+01:002026-01-06|Building guide|Comments Off on Roof coverings and the buildings they suit
Back to top