About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

How to choose screws and fix insulated wall panels with a mineral wool core?

A screw for insulated wall panels is selected for the entire connection. The panel thickness, the material and thickness of the support, the load and the corrosive conditions all matter. The geometry of the head and the sealing are also important. There is no single length or number of screws that is correct for every wall with a mineral wool core. The fixing pattern should follow from the design and the panel documentation. Correct seating is just as important as the choice of fastener itself. First establish the type and thickness of the panel and the arrangement of the joint. Then check the support. A screw for thin-walled steel profiles may have a different tip and drilling range than a fastener for thick steel. Timber and concrete require solutions intended for these substrates.

By |2026-11-14T09:54:44+01:002025-11-27|Building guide|Comments Off on How to choose screws and fix insulated wall panels with a mineral wool core?

A heated workshop with fibre cement roofing: the roof build-up and working comfort

In a workshop, a stable working environment matters, not just sheltering tools from the rain. Heating, wet vehicles and running equipment create conditions different from an open carport. Fibre cement sheets can be the covering of such a building, but comfort requires a complete layer build-up. Asbestos-free fibre cement is not a thermal solution on its own. Before buying, it is worth defining the working temperature, operating hours, sources of moisture and the services required. A workshop used daily and a room heated for a few hours react differently. With intermittent heating, the structure and covering may remain cold while the air inside warms up quickly. If it contains a lot of moisture, the importance of a correct layer build-up and ventilation increases.

By |2026-11-15T17:56:41+01:002025-11-25|Building guide|Comments Off on A heated workshop with fibre cement roofing: the roof build-up and working comfort

Insulating a wall plate where the roof meets the wall

Insulating the wall plate must be considered together with the whole junction where timber, the ring beam, the eaves and the roof layers meet. Above all, check whether the roof-slope insulation actually connects to the wall layer rather than merely sitting next to it on a drawing. The article compares mineral wool and PIR boards, discusses eaves ventilation and the sequence of work on an existing detail. Material choice depends on the available space and the adopted layer arrangement, so the structural decision is left to the designer.

By |2026-11-14T22:52:58+01:002025-11-19|Building guide|Comments Off on Insulating a wall plate where the roof meets the wall

Fibre cement roofing above an insulated loft: layers and junctions

A covering over a habitable loft must work together with the layers that provide warmth, dryness and comfort. A durable outer surface alone is not enough. Fibre cement sheets can be included in such a roof if the whole solution meets the building's requirements. Asbestos-free fibre cement acts here as the covering, not as a ready-made insulated panel. The junctions between layers at walls, windows and service penetrations require the most attention. The insulation may be located in the roof slope or in the ceiling separating an unused space. These are different arrangements. If the loft is to be habitable, the thermal envelope should encompass all used parts. Knee walls, slopes and junctions with the ceiling must be checked.

By |2026-11-15T17:56:38+01:002025-11-16|Building guide|Comments Off on Fibre cement roofing above an insulated loft: layers and junctions

Preventing roof leaks during installation

Roof tightness depends primarily on roof pitch, the quality of joints and the way water is drained, not on the sheet metal alone. Check the specified pitch against the installation instructions for the selected covering. T18, T35 and tile-effect sheets need not share the same limits. It is also worth tracing the entire water path from ridge to eaves, checking the choice of underlay and planning flashings at the chimney and service penetrations. The key decision concerns the compatibility of the covering with the roof geometry and fixing system, not the number of sealants.

By |2026-11-14T19:21:59+01:002025-11-16|Building guide|Comments Off on Preventing roof leaks during installation

How do you choose the thickness of an insulated wall panel with a mineral wool core?

The thickness of an insulated wall panel with a mineral wool core is selected simultaneously for thermal performance, fire requirements and the method of support. It is not enough to take 100 mm because that variant is readily available. First, the wall's task and the conditions in the building must be defined. Then the specific panel data sheets and the cost of the whole solution are compared. The right choice reduces the risk of later additional insulation or structural reconstruction. Note whether it is a façade, an internal partition or an element with a specific fire function. State the temperatures on both sides and how the rooms are used. Take into account moisture, frequent washing and the possibility of changing the hall's function. This is the information that allows the requirements to be determined.

By |2026-11-14T09:55:06+01:002025-11-10|Building guide|Comments Off on How do you choose the thickness of an insulated wall panel with a mineral wool core?

Can trapezoidal steel roofing suit a traditional house?

Trapezoidal sheet metal can suit a traditional-style house if its profile, colour and details work with the building form and surroundings. Rather than following a generic recommendation, assess the whole composition: roof proportions, eaves, chimney and façade materials. Check whether the chosen variant disrupts the existing arrangement and whether its technical parameters match the structure and pitch. Compare samples under different lighting conditions and analyse the details at the roof edges. The decision should come from fitting the specific building, not from the name of the covering alone.

By |2026-11-14T19:19:29+01:002025-11-09|Building guide|Comments Off on Can trapezoidal steel roofing suit a traditional house?

PIR roof panel or EPS-core panel? How to compare the options

A PIR roof panel usually achieves better thermal insulation at a smaller thickness than a comparable EPS-core panel. The polystyrene variant can be cost-effective and lightweight. However, the choice should be governed by the requirements of the entire roof. U-value, loads, the range of fire classifications, coatings and installation cost must be compared. The same thickness does not mean the same thermal function. An insulated roof panel has metal facings and a bonded core. Its price should not be compared directly with a PIR insulation board alone or a pack of EPS. These materials require other layers to form a roof. In both panel variants, the outer profile and the joints are part of the roofing system.

By |2026-11-14T12:18:14+01:002025-10-24|Building guide|Comments Off on PIR roof panel or EPS-core panel? How to compare the options

Roofs without overhanging eaves: what to plan before building

A roof without eaves is one where the edge of the slope sits close to or flush with the façade rather than projecting beyond it. Before building, it is worth establishing how water will drain away and where the service points will be. Check the junction detail between roof and wall, the continuity of insulation, and access to the gutter and downpipe. Whether the gutter stays visible or is concealed depends on the chosen detail. Also remember ventilation and the coordination of roofing, insulation and façade work.

By |2026-11-14T22:52:53+01:002025-10-21|Building guide|Comments Off on Roofs without overhanging eaves: what to plan before building

T18 trapezoidal steel sheets: dimensions and support spacing

T18 trapezoidal steel sheet is suitable for many roofs and façades, but the profile name alone is not enough to place an order. You need to check the cover width, steel thickness and sheet variant. The support spacing depends on the loads and the tables for the specific product. Two sheets marked T18 may have a different width, a different cross-section and different installation conditions. Below we show how to read this data and use it when taking measurements. The number in the name refers to the nominal height of the rib. It does not describe the steel thickness, sheet length or cover width. T18 from two different production lines does not have to have identical ribs.

By |2026-11-14T09:50:36+01:002025-10-12|Building guide|Comments Off on T18 trapezoidal steel sheets: dimensions and support spacing
Back to top