+48 500 409 109

What leads to complaints about steel roofing sheets and how can problems be avoided?

A roofing sheet complaint rarely has one obvious cause, so before blaming the material or the installation, establish at which stage the visible symptom appeared. Check the delivery acceptance record, storage conditions, how the sheets were handled and compliance with the product instructions. This article explains how to distinguish a leak from discolouration and deformation, why earlier work on the roof matters and why a well-described report can be more useful than a single photograph of the fault.

By |2026-11-15T03:02:35+01:002026-03-16|Building guide|Comments Off on What leads to complaints about steel roofing sheets and how can problems be avoided?
Read More

Selecting roof cladding for an industrial building

The choice of roof covering for an industrial hall depends primarily on the building structure, the processes inside and the anticipated loads. It is worth establishing whether the roof is to be insulated and what fire and acoustic requirements apply. Sandwich panels and built-up systems on structural steel decking are only examples; T18 and T35 profiles do not automatically replace the others. The description should cover temperature, humidity, dust and possible chemical exposure, as well as future changes in use. Ultimately, complete roof assemblies are compared, not individual materials.

By |2026-11-14T19:20:14+01:002026-03-15|Building guide|Comments Off on Selecting roof cladding for an industrial building
Read More

How coating and drainage protect gutter aprons from moisture

The gutter aprons (drip-edge flashings) work where water leaves the roof covering and enters the gutter. Their durability depends on both the material and unobstructed drainage. Even well-protected sheet metal will not solve the problem of standing water or accumulated debris. When choosing, it is therefore worth combining an assessment of the coating with an assessment of the entire eaves detail. This makes better use of the flashing's advantages and reduces the places requiring later repairs. At the eaves, water runs off a larger roof area. The gutter apron should carry it away in a planned manner. The position of its end relative to the gutter is important. Choosing a more expensive coating alone will not fix incorrect positioning.

By |2026-11-15T03:03:33+01:002026-03-13|Building guide|Comments Off on How coating and drainage protect gutter aprons from moisture
Read More

Comparing sandwich panels by core, price and intended use

Compare insulated panels by the building task first, and only then by price. A wall, a roof and a cold store need different details. PIR helps to reduce insulation thickness, while mineral wool may better meet the fire requirements of a specific system. However, the result is determined by the parameters of the finished panel, its facings, the joint and the installation. The core name alone is not enough to choose a material. A wall panel forms the vertical envelope. Its facing can be smooth or lightly profiled. Solutions with visible and concealed fixing are available. The laying direction must be matched to the documentation and the structure. Vertical and horizontal are not merely two versions of the appearance of the same façade.

By |2026-11-14T12:16:47+01:002026-02-28|Building guide|Comments Off on Comparing sandwich panels by core, price and intended use
Read More

Protecting sheet metal roofing against rust at edges and fixings

Protecting a metal roof from corrosion depends above all on matching the coating to the conditions around and inside the building. It is worth checking whether the chosen variant is permitted for the given environment, what its application limits are and what maintenance it requires. Neither the colour alone nor a declared warranty determines how effective the protection will be. The sections that follow cover transport, cutting, drainage and upkeep, which influence the durability of the covering just as much.

By |2026-11-15T03:00:31+01:002026-02-24|Building guide|Comments Off on Protecting sheet metal roofing against rust at edges and fixings
Read More

Trapezoidal steel sheet weights: calculating the mass of an order

The weight of trapezoidal sheet is determined mainly by thickness, material and profile geometry, not by the height of the trapezoid alone. Before comparing offers, check whether the stated value refers to a gross, effective or running metre, as this is the most common source of error. For an order, the total weight of all sheets together with flashings and packaging matters, while for roof design the other layers and loads also count. Choosing thinner sheet may reduce stiffness and permissible span, so leave the decision on the section to the designer.

By |2026-11-14T19:21:19+01:002026-02-22|Building guide|Comments Off on Trapezoidal steel sheet weights: calculating the mass of an order
Read More

Designing the connection between a steel building and its foundations

The connection between a steel hall and its foundation requires calculation of the entire node. Anchors, base plate, concrete, grout and the method of transferring forces are selected. A chemical anchor is one of the available solutions, but it does not suit every hall automatically. The bar diameter and hole depth should not be chosen on the basis of the building's mass or general advice. The entire connection system is checked. The base transfers vertical and horizontal forces as well as moments resulting from the structure's behaviour. Wind can cause part of the connection to be lifted, even though the entire hall is heavy. Loads depend on the frame layout, bracing and location conditions. Therefore the number of anchors does not simply follow from the size of the base plate.

By |2026-11-14T12:16:13+01:002026-02-21|Building guide|Comments Off on Designing the connection between a steel building and its foundations
Read More

Single- or double-module roofing sheets: what difference does the format make?

The number of modules in a metal roofing tile determines how many repeating pattern rows an individual sheet contains, not the number of corrugations across its width. Before choosing a format, compare the effective coverage area rather than the external dimensions, and analyse the cutting layout for the specific roof geometry. Also check whether offcuts can be reused and how installation costs compare. It is worth comparing two cutting plans, the number of pieces and the required flashings. The final choice depends on the roof layout and work organisation, so leave detailed technical decisions to the designer.

By |2026-11-14T16:08:24+01:002026-02-16|Building guide|Comments Off on Single- or double-module roofing sheets: what difference does the format make?
Read More

What does an eaves flashing do at the gutter?

The over-gutter flashing is the trim that takes water from the roof slope and directs it into the gutter, but it works effectively only when matched to the specific eaves detail. Before ordering, check whether its profile suits the gutter height, the roof covering overhang and the membrane layout. Its cooperation with ventilation is also crucial, as is distinguishing it from the under-gutter flashing, which serves a different purpose. The article discusses these relationships and the consequences of incorrect selection and installation.

By |2026-11-14T22:54:49+01:002026-02-15|Building guide|Comments Off on What does an eaves flashing do at the gutter?
Read More

Where is T35 trapezoidal steel sheet suitable and what does its load-bearing capacity depend on?

T35 is a profile chosen for roofs and cladding requiring a greater profile height than T18. However, the suitability of the sheet is determined by the entire cross-section, thickness and steel grade. The symbol alone does not specify the permissible support spacing. Before purchase, the coverage width, profile side and installation conditions must also be established. This allows products to be compared without confusing the dimensions and load-bearing capacities of different variants. Sheet with this profile can be found on garages, agricultural buildings, workshops and halls. It is also sometimes used on façades. Its pronounced ribs give the surface a technical character. From a design perspective, however, transferring loads to the purlins or battens is more important than appearance.

By |2026-11-14T09:50:45+01:002026-02-13|Building guide|Comments Off on Where is T35 trapezoidal steel sheet suitable and what does its load-bearing capacity depend on?
Read More
Back to top