Preparing a metal roof for repainting

Painting a sheet-metal roof makes sense only when the metal is sound and the old coatings and causes of damage have been identified. This guide gives owners and contractors the criteria for judging whether a covering is suitable for renovation and the steps needed to prepare it. It is worth checking the degree of corrosion, coating adhesion and the condition of fixings, as well as the underside of the sheets, where rust will not disappear after painting. Removing the source of recurring damage before new paint protects the prepared substrate is equally decisive.

By |2026-11-14T19:20:59+01:002024-03-09|Building guide|Comments Off on Preparing a metal roof for repainting

How do you calculate the required thickness of PIR board for a wall?

The required PIR thickness can be preliminarily calculated from the required thermal resistance of the wall. However, you need to know the existing layers and the parameters of the selected board. A calculator based only on the type of masonry gives too little information. The final selection also takes into account fixings, thermal bridges, moisture and the method of finishing. The calculation result must be translated into an available product suitable for the application. Record all wall layers, their thicknesses and thermal properties. Include existing insulation and voids, if they actually occur. For an old house, the documentation may need to be verified on site. Do not assume that every brick or aerated concrete wall has the same resistance.

By |2026-11-14T09:55:59+01:002024-03-05|Building guide|Comments Off on How do you calculate the required thickness of PIR board for a wall?

Choosing a roof covering for a garage

The choice of garage roof covering depends primarily on how the interior will be used, not on the roof area alone. Check whether the garage will be heated, whether it will serve as a workshop, and what pitch and support spacing the design specifies. A wet car brings moisture into an unheated garage. Plan how to keep rain out, drain it away and ventilate the space so that moisture does not collect under the sheets. A sandwich panel combines layers into one element, but its thickness and fire resistance must be selected. Compare complete systems, not just the sheets.

By |2026-11-14T19:21:43+01:002024-03-05|Building guide|Comments Off on Choosing a roof covering for a garage

How do you assess heat and moisture transfer through a building element?

A reliable result starts with a correct description of the wall or roof. You need to know all the layers, their thicknesses and properties, as well as the conditions on both sides of the building envelope. The low lambda of PIR helps to reduce the insulation thickness. However, it is not enough to assess the entire system. The thermal calculation must be supplemented by checking moisture, thermal bridges and the airtightness of joints. Record the layer build-up from the interior to the exterior. Include plaster, masonry, existing insulation, air cavity and finish. Do not omit old insulation just because it will not be replaced. During renovation, its condition and actual thickness may require an inspection opening. A photo of the façade does not provide this data.

By |2026-11-14T09:55:23+01:002024-03-01|Building guide|Comments Off on How do you assess heat and moisture transfer through a building element?

Choosing a supporting deck and underlay beneath a roof covering

The choice of substrate and underlay depends primarily on whether the roofing system requires full boarding or just a batten grid. This article gives you the criteria to assess whether a membrane is suitable for contact with insulation or a rigid substrate, how roof pitch affects requirements, and why ventilation and vapour control matter. Check how the selection of these elements affects the roof's ability to dry out and what consequences changing one of them has. Remember that design decisions remain with the designer.

By |2026-11-14T22:55:10+01:002024-02-27|Building guide|Comments Off on Choosing a supporting deck and underlay beneath a roof covering

A leaking roof: how to trace the cause and decide what to do next

First limit damage inside and have the roof inspected, rather than immediately looking for the culprit at the wet patch. Water may travel along the membrane or structure, and a hole visible above a stain is not always the source of the leak. It is worth establishing whether the problem occurs with every rain or only with rain from a particular wind direction, and distinguishing precipitation from water-vapour condensation. The check should cover valleys, chimney flashings, wall junctions and service penetrations. An effective repair removes the cause instead of covering an arbitrary section of the roof slope.

By |2026-11-14T16:07:59+01:002024-02-26|Building guide|Comments Off on A leaking roof: how to trace the cause and decide what to do next

Four checks when selecting a tile-effect metal roof covering

Begin by establishing whether the chosen roofing tile profile actually suits the roof geometry and the intended method of installation, rather than by comparing colours. Check its conformity with the design, the specification of the steel and workmanship, the suitability of the coating for the surrounding conditions, and the full cost of the finished roof including delivery. Any one of these points may rule out a seemingly attractive offer. Only once they have been set side by side is it worth deciding between similar variants, since the appearance of a sample alone will not reveal technical differences.

By |2026-11-15T03:01:32+01:002024-02-18|Building guide|Comments Off on Four checks when selecting a tile-effect metal roof covering

Building a watertight flat roof: design details and limitations

The watertightness of a flat roof depends above all on a coherent layer system, not on the covering material alone. Before construction, it is worth establishing how water will be drained, who will service the surface and how, and whether the roof is to serve additional functions. Falls, waterproofing, outlets and continuity of insulation form a whole in which every element must fit together. PIR boards can be part of such a system, but they do not replace a watertight covering. The project and the care taken over details determine success.

By |2026-11-14T22:54:04+01:002024-02-16|Building guide|Comments Off on Building a watertight flat roof: design details and limitations

When a cheaper roof covering raises the total cost

A lower price for the covering does not always mean a cheaper roof — what matters is whether the material meets the project requirements and suits the entire roof slope. Before comparing offers, check whether the running metres share the same basis of settlement, whether the product name confirms the parameters, and what the scope of accessories and labour includes. Saving makes sense when it reduces waste and unnecessary complications rather than omitting necessary layers. Compare the cost of the finished solution and its later maintenance, not just the price of a sheet.

By |2026-11-14T19:19:48+01:002024-02-12|Building guide|Comments Off on When a cheaper roof covering raises the total cost

Can a metal roof work on an energy-efficient home?

Metal sheeting suits an energy-efficient house only as part of a complete, well-considered roof assembly, not as a stand-alone solution. Before approving the design, it is worth checking the continuity of insulation, air tightness and how the eaves, ridge and service penetrations are detailed. Equally important are the declared lambda of the insulating material and the choice of counter-batten fixings capable of carrying the covering loads. Whether the roof meets its targets depends on how all layers work together with the rest of the building, so the thermal assessment should cover the whole assembly rather than a single sheet.

By |2026-11-14T16:08:03+01:002024-02-10|Building guide|Comments Off on Can a metal roof work on an energy-efficient home?
Back to top