About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

What determines the right insulation material for a roof?

The choice of roof insulation material depends above all on where the heated boundary runs and on the ventilation plan, not on the product name alone. Check which building elements separate the interior from the outside, then compare lambda, thermal resistance and the U-value for the whole assembly. It is also worth establishing whether limited thickness, moisture protection or continuity of insulation is the key issue. Only on that basis should you consider PIR, mineral wool, EPS or XPS, bearing in mind that the overall effect depends on the complete layer build-up and careful joints.

By |2026-11-15T03:01:36+01:002024-12-05|Building guide|Comments Off on What determines the right insulation material for a roof?

How to coordinate the roof colour with the façade, windows and doors

First establish which elements of the building will remain unchanged, and only then choose the colour scheme around them. This guide shows how to reconcile the roof colour with the façade, joinery and guttering without losing the coherence of the whole composition. Check whether the chosen palette is permitted for your plot, how different materials display the same shade, and why samples should be viewed outdoors. Also consider matt versus gloss, surface texture and the working conditions of dark sandwich panels. This information will help you narrow the choice deliberately and avoid an accidental mixture.

By |2026-11-14T22:55:55+01:002024-12-04|Building guide|Comments Off on How to coordinate the roof colour with the façade, windows and doors

Selecting rooflights for a hall, garage or other building

When choosing between a point rooflight and a continuous run, the deciding factors are chiefly the building's internal arrangement and how the roof is constructed. A point unit lights one defined portion of the slope and can be aimed at a particular spot, while a continuous run is longer and uses a different support layout, which may suit a hall with a large floor area. You should also confirm compatibility with the specific covering, how the base and insulation of the complete element are detailed, and whether ventilation or smoke extraction is required. Position rooflights in relation to room layout and structure, not merely total glazed area.

By |2026-11-14T22:55:33+01:002024-12-03|Building guide|Comments Off on Selecting rooflights for a hall, garage or other building

What is a roof valley and how do you keep it watertight?

Whether a roof valley stays watertight depends above all on a correctly shaped drainage path, not on the appearance of the visible strip alone. The building owner and the contractor should jointly check that the width and shape of the flashing match the catchment area, the roof pitch and the ease of clearing debris. Support, continuity of the underlay and the way sheets terminate at the valley are equally important. This article explains these relationships and the consequences of narrowing the detail too tightly for water flow.

By |2026-11-14T22:54:00+01:002024-11-30|Building guide|Comments Off on What is a roof valley and how do you keep it watertight?

What is tile-effect metal roofing made of and what determines its quality?

Tile-effect metal roofing is a profiled covering made of thin sheet metal protected against corrosion. Its quality is determined by the steel core, the metallic coating, the organic layers and the precision of the pressings. The compatibility of the entire installation system is also important. Colour does not describe durability, and a long guarantee does not replace checking the conditions of use. It is worth knowing which information from the product data sheet relates to the steel and which to the surface. The core gives the sheet its mechanical properties. Its thickness and grade work together with the shape of the profile. A thin flat strip behaves differently after pressing than before forming. However, this does not mean that geometry will replace steel thickness at will.

By |2026-11-14T09:54:06+01:002024-11-30|Building guide|Comments Off on What is tile-effect metal roofing made of and what determines its quality?

When do thicker insulated panels make little difference to a steel building?

A thicker core usually improves the insulation of a given panel, but not every subsequent change brings a similar effect for the whole building. A steel hall also loses heat through gates, the floor and ventilation. Before you order the thickest wall variant, it is worth checking whether this particular partition is where the additional expense is most justified. Panels of the same thickness can have different properties. The core, facings and joint construction matter. A declared thermal transmittance of the selected product is needed for comparison. A steel hall should receive an enclosure that meets the project requirements, not merely a general description of the material.

By |2026-11-15T03:02:58+01:002024-11-22|Building guide|Comments Off on When do thicker insulated panels make little difference to a steel building?

What determines rafter size and spacing on a roof?

The cross-section and spacing of rafters are determined by structural calculations, not just the type of roofing. To select the right dimensions, check the rafter length between supports, roof pitch, building location, height and surroundings, as well as the planned roofing, insulation and attic build-up. It is also essential to establish the structural scheme, i.e. the support conditions and connections to the truss. These data must be passed to the designer, who will verify load capacity and deflection; ready-made tables can only serve as a guide.

By |2026-11-14T16:06:55+01:002024-11-21|Building guide|Comments Off on What determines rafter size and spacing on a roof?

Where cold-formed sections carry loads between the frame and the cladding

In a steel hall, not every element performs the same function. Main frames, purlins, rails and lattice girders form successive parts of the system. Cold-formed profiles may appear in several of them, but each time the load path must be defined. This helps to select the section correctly and to establish responsibility for the details. Z-sections, C-sections, sigmas and omegas are not simply different ways of filling the space between columns. Wind acting on the wall panel reaches its supports through the fasteners. The forces then pass through the rails or other elements to the main structure. On the roof, purlins perform a similar role. The entire chain must be verified, including the connections. Correct selection of one segment does not yet confirm the safety of the complete load path.

By |2026-11-15T03:03:19+01:002024-11-15|Building guide|Comments Off on Where cold-formed sections carry loads between the frame and the cladding

What are the advantages of steel exterior window sills?

A steel external window sill primarily drains water from beneath the window and protects the façade, so when choosing one it is worth looking not only at colour but at the fall, drip edge and connection to the window. Coated sheet metal offers wide scope to match gutters, roof or joinery, and its low weight makes transport and work easier. Compare physical samples under the same lighting before ordering. Differences in gloss and texture can be hard to see on a screen.

By |2026-11-14T19:20:34+01:002024-11-14|Building guide|Comments Off on What are the advantages of steel exterior window sills?

Five roofing defects to look for before accepting the work

Before accepting a metal roof, it is worth checking not only the colour of the covering but above all the quality of the substrate, the direction of the laps, the choice of fasteners, the condition of the coating and the patency of ventilation and drainage. These five areas help catch errors that remain invisible from street level. The building owner should plan a stage-by-stage inspection and agree with the contractor when to review the battens, the underlay and the key flashings. What matters is documenting the places later covered, so the assessment does not rely solely on a general view.

By |2026-11-14T22:55:08+01:002024-11-13|Building guide|Comments Off on Five roofing defects to look for before accepting the work
Back to top