About PiVi

This author has not yet filled in any details.
So far PiVi has created 1503 blog entries.

Why vacuuming the gutters alone may leave them unready for winter

Vacuuming the gutters alone is usually not enough before winter, as it mainly removes loose leaves and does not confirm that the whole drainage system works. The owner should check sediment at the base and joints, the flow through outlets and downpipes, and the tightness of connections. Whether a vacuum suffices depends on the home's surroundings and the actual condition of the system, so it is worth assessing what remains after cleaning. The inspection also covers fixings and drainage without standing water, so cleaning is only one of its stages.

By |2026-11-15T03:01:38+01:002025-02-17|Building guide|Comments Off on Why vacuuming the gutters alone may leave them unready for winter

Can solar panels be mounted safely on a sheet metal roof?

A photovoltaic system can be installed safely on a metal roof when the structure, mounts and seals are compatible. The key variable is load capacity where loads are actually transferred, not the roof's appearance. Before deciding, check the structural documentation, its current condition, and the state of the covering and layers beneath. Account for installation weight, wind and snow forces, and service access. The type of sheet determines the fixing method, so do not transfer solutions between profiles without verification.

By |2026-11-14T16:08:39+01:002025-02-17|Building guide|Comments Off on Can solar panels be mounted safely on a sheet metal roof?

Roof framing: how the parts work together and what determines the layout

Whether a roof structure is safe depends not only on the selection of cross-sections but above all on checking the entire load path from the covering through the truss members to the supports. It is worth verifying that the layout matches the building span and the attic plan, and that the connections and anchorages transfer forces without displacement. When replacing the covering or changing the attic function, an assessment of the existing structure by a designer is essential, taking into account the new loads and support conditions.

By |2026-11-14T16:06:52+01:002025-02-12|Building guide|Comments Off on Roof framing: how the parts work together and what determines the layout

From a building model to steel section production: completing the technical documentation

The structural model shows the position of elements, but it does not always contain everything the production plant needs. Full hole patterns, part orientation or a coating description may be missing. A material schedule, in turn, does not automatically clarify node details. Passing cold-formed profiles to production therefore requires organising several types of information. The aim is one consistent description of the finished element. It must be clear who selects the cross-section, who develops the connections and who produces the workshop documentation. Roles may be divided among several parties. They should not, however, leave an undescribed space between the general design and the finished part. Each scope requires clear confirmation.

By |2026-11-15T17:50:37+01:002025-02-10|Building guide|Comments Off on From a building model to steel section production: completing the technical documentation

How to choose a roofer for a complex roof

You can recognise a roofer to whom a difficult roof can be entrusted by how they prepare and carry out the work, not by a photograph of the finished slope alone. Before deciding, check whether they can point to the instructions for the chosen covering and explain which drawings apply to your roof, and ask about projects with a similar geometry and type of covering. Ask also how they document the stages that will be covered and how they report problems with the substrate. Questions about details at the chimney, valley and eaves will tell you more than a general view of the building.

By |2026-11-14T16:09:01+01:002025-02-03|Building guide|Comments Off on How to choose a roofer for a complex roof

PIR or XPS for a flat roof? How to choose insulation for the layer build-up

PIR and XPS can be used on flat roofs, but they do not perform the same role in every build-up. PIR allows the layer thickness to be reduced. XPS can be advantageous where the insulation is exposed to water and high loads. First, the sequence of layers and the way the roof is used must be established. Only then should a specific board, its parameters and its cost be compared. In a traditional roof, the thermal insulation is located beneath the waterproofing layer. In such a build-up, PIR can be installed on a suitably prepared substrate together with the specified vapour control. Above it, waterproofing matched to the entire system is applied.

By |2026-11-14T09:56:16+01:002025-02-01|Building guide|Comments Off on PIR or XPS for a flat roof? How to choose insulation for the layer build-up

When is tile-effect metal roofing a good choice for a new or existing roof?

Blachodachówka is worth considering when its profile suits the roof pitch, the roof structure and the intended appearance of the house. Before comparing prices, however, check the manufacturer's documentation for the permitted slope, the required batten layout and the fixing method — these determine whether a given model is suitable for your roof at all. For a renovation, also assess the condition of the roof trusses, the old layers and any signs of damp, because a lightweight blachodachówka will not repair a weakened structure. Only then compare complete roofing variants rather than the price of a single sheet.

By |2026-11-14T16:09:05+01:002025-01-29|Building guide|Comments Off on When is tile-effect metal roofing a good choice for a new or existing roof?

Preparing roof battens for T18 and T35 trapezoidal sheets

The spacing of battens under trapezoidal sheeting is determined by the load capacity of the specific sheet and the roof loads, not by one universal module. It is therefore worth checking whether the chosen profile and its documentation match the support scheme, roof pitch and site conditions. Also consider the condition of the structure, the evenness of the supports and the layer arrangement. T18 and T35 require separate selection of thickness and fixings, and the designation alone is not enough. Below we discuss the choices facing the building owner and the contractor, and the trade-offs to consider before installation.

By |2026-11-14T22:53:22+01:002025-01-27|Building guide|Comments Off on Preparing roof battens for T18 and T35 trapezoidal sheets

What does the Polish term ‘płyta obornicka’ mean, and where are these panels used?

The name “płyta obornicka” is a colloquial term for a sandwich panel, so when choosing one you should first check the full product specification rather than the name alone. The order should state the building’s function, panel type, core type, thickness, required parameters, facings, coatings, colour, module and lengths, and include the layout of supports and openings. The name alone does not indicate the core type, thickness or whether the panel is for a wall or roof, so comparing offers requires reference to the data sheet and instructions for the specific product.

By |2026-11-14T16:06:31+01:002025-01-23|Building guide|Comments Off on What does the Polish term ‘płyta obornicka’ mean, and where are these panels used?

What makes up the cost of an insulated panel roof?

The cost of an insulated panel roof includes far more than the purchase of the panels. Flashings, fixings, seals, transport, unloading and installation must be added. Supports and openings in the roof slope also matter. A reliable comparison of quotes requires the same specification and the same scope of work. The price per square metre of panel does not equal the price per square metre of a finished, weathertight roof. First establish what the given amount covers. It may be the price of material, the covering with installation, or the entire roof including the structure. These are different scopes. Also check whether the figure is net or gross and what area was used for settlement. Compare short advertisements without a specification with particular caution.

By |2026-11-14T12:17:24+01:002025-01-21|Building guide|Comments Off on What makes up the cost of an insulated panel roof?
Back to top