+48 500 409 109

How can you reduce the cost of buying insulated panels without losing the required parameters?

The cost of insulated panels can be reduced through good cutting optimisation, a consistent order and matching the parameters to the project. Too thin a core, a random coating or missing installation parts only give apparent savings. First establish the wall and roof requirements. Then compare complete quotes for the same quantity of material. Also count the waste, delivery, unloading and work on site. In the enquiry, specify the intended use of the panel, the type of core, the thickness and the required thermal transmittance. State the conditions on both sides of the enclosure. A wall of an unheated warehouse has a different task from the enclosure of a room with a wet process. The fire, acoustic and structural requirements follow from the design.

By |2026-11-14T12:16:42+01:002025-12-15|Building guide|Comments Off on How can you reduce the cost of buying insulated panels without losing the required parameters?
Read More

How to choose the thickness of an insulated roof panel for a garage?

The garage roof is selected according to heating, moisture and loads. There is no single panel thickness suitable for every building. An unheated garage, a workshop and a room connected to the house place different demands. In addition to thermal insulation, supports, slope, seals and ventilation are important. A thinner panel may be sufficient in one project and unsuitable in another. This is the first question before choosing a thickness. In a continuously heated garage, limiting heat loss matters. In an unheated one, insulation slows temperature changes but does not by itself ensure a positive temperature throughout the winter. The required effect should be described without assuming that the material will replace a heat source.

By |2026-11-14T12:17:59+01:002025-12-12|Building guide|Comments Off on How to choose the thickness of an insulated roof panel for a garage?
Read More

How do you choose the length of insulated panels for the building and transport?

The length of an insulated panel is matched to the building geometry, the supports and the delivery options. The longest available panel does not always reduce the cost. It may require a different vehicle, unloading equipment and a different lifting method. Dividing it into shorter elements, in turn, creates additional joints. A good length schedule is based on verified dimensions, details and the documentation for the selected system. Panels are often made to the length specified in the order, but within the limits for the given product. For example, a PIR roof panel has a range of 2 to 16 m in its data sheet. The maximum depends on the colour and thickness. This is not a promise that every 16 m panel can be used in any layout.

By |2026-11-14T12:17:22+01:002025-12-02|Building guide|Comments Off on How do you choose the length of insulated panels for the building and transport?
Read More

How to choose screws and fix insulated wall panels with a mineral wool core?

A screw for insulated wall panels is selected for the entire connection. The panel thickness, the material and thickness of the support, the load and the corrosive conditions all matter. The geometry of the head and the sealing are also important. There is no single length or number of screws that is correct for every wall with a mineral wool core. The fixing pattern should follow from the design and the panel documentation. Correct seating is just as important as the choice of fastener itself. First establish the type and thickness of the panel and the arrangement of the joint. Then check the support. A screw for thin-walled steel profiles may have a different tip and drilling range than a fastener for thick steel. Timber and concrete require solutions intended for these substrates.

By |2026-11-14T09:54:44+01:002025-11-27|Building guide|Comments Off on How to choose screws and fix insulated wall panels with a mineral wool core?
Read More

How do you choose the thickness of an insulated wall panel with a mineral wool core?

The thickness of an insulated wall panel with a mineral wool core is selected simultaneously for thermal performance, fire requirements and the method of support. It is not enough to take 100 mm because that variant is readily available. First, the wall's task and the conditions in the building must be defined. Then the specific panel data sheets and the cost of the whole solution are compared. The right choice reduces the risk of later additional insulation or structural reconstruction. Note whether it is a façade, an internal partition or an element with a specific fire function. State the temperatures on both sides and how the rooms are used. Take into account moisture, frequent washing and the possibility of changing the hall's function. This is the information that allows the requirements to be determined.

By |2026-11-14T09:55:06+01:002025-11-10|Building guide|Comments Off on How do you choose the thickness of an insulated wall panel with a mineral wool core?
Read More

What is a 100 mm mineral wool insulated wall panel suitable for?

A 100 mm wall panel with a mineral wool core can be used for cladding halls and selected internal partitions. However, it is not a universal solution for every heated building. Its U-value, mass, acoustics and fire resistance depend on the specific system. Before purchase, the support, coating and locks must also be checked. The same thickness in two offers does not mean the same properties. In one of the wall panels with 100 kg/m³ stone wool, the 100 mm variant has a Uc of 0.39 W/(m²·K). With 0.5/0.5 mm facings, the mass is 18.1 kg/m². The datasheet states Rw 33 dB and a reaction to fire of A2-s1,d0.

By |2026-11-14T09:55:04+01:002025-10-02|Building guide|Comments Off on What is a 100 mm mineral wool insulated wall panel suitable for?
Read More

Buying sandwich panels in Lower Silesia: how to assess a supplier

When buying insulated panels in Lower Silesia, distance from the stock is not the only consideration. More important are the material's conformity with the design, the possibility of inspecting the batch and efficient delivery to the site. A local point may facilitate collection, but a more distant supplier can be more advantageous for a full load. Compare the ready delivery of the required panels, not just the seller's address. Start with the type of panel. Determine whether you need wall, roof or cold-storage panels. Specify the thickness, core and required parameters. Include lengths and quantities. The phrase '100 mm panel' alone is not enough. Different panels may have a different joint, cover width, load-bearing capacity and facing thicknesses.

By |2026-11-14T12:15:51+01:002025-09-18|Building guide|Comments Off on Buying sandwich panels in Lower Silesia: how to assess a supplier
Read More

When is it worth choosing a 150 or 200 mm insulated wall panel?

150 or 200 mm wall panels are worth considering when the project requires better thermal insulation or a specific fire resistance. However, a large thickness alone does not confirm suitability. The type of core, the joint, the facings and the method of support all matter. In the case of mineral wool, the weight of long elements must also be taken into account. The choice between 150 and 200 mm should follow from calculations and the cost of the complete wall. With the same material, a greater thickness increases the thermal resistance of the layer. In one mineral wool wall panel, the 150 mm variant has Uc 0.27 W/(m²·K), while the 200 mm achieves 0.20. This is a noticeable difference, but it applies to a specific system.

By |2026-11-14T09:55:00+01:002025-09-06|Building guide|Comments Off on When is it worth choosing a 150 or 200 mm insulated wall panel?
Read More

How much does it cost to build a steel-framed hall with insulated sandwich panels, including installation?

The price of a hall made from sandwich panels depends on whether the quote covers just the cladding, the structure, or a building ready for use. The budget also includes foundations, floor slab, gates, services and installation. Without defining the scope, the rate per square metre of the hall explains little. A reliable cost estimate begins with the building's function, geometry and site conditions. Only then are materials and quotes compared. The panels form the walls and roof, but usually work with a separate load-bearing structure. Their price does not automatically include columns, purlins, foundations or the floor slab. The cladding is one part of the building. A price list for the panel alone does not allow you to calculate the cost of a hall ready for business.

By |2026-11-14T12:17:43+01:002025-08-24|Building guide|Comments Off on How much does it cost to build a steel-framed hall with insulated sandwich panels, including installation?
Read More

How to choose an insulated wall panel with mineral wool for a specific building?

An insulated wall panel with mineral wool is best chosen starting from the building's requirements. First, fire protection, thermal insulation and wind load are determined. Then the fixing arrangement, coating and dimensions are checked. A panel with a higher core density is not automatically better in every respect. A good specification allows offers for the same solution to be compared and avoids surcharges during installation. Describe the function of the facility and the temperature that will be maintained in it. State whether the wall is external, a partition or is to separate a fire zone. The enclosure of an unheated warehouse has a different task from the wall of a hall with employees and a humid process. The building's location and planned openings are also important.

By |2026-11-14T09:54:24+01:002025-07-18|Building guide|Comments Off on How to choose an insulated wall panel with mineral wool for a specific building?
Read More
Back to top