Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Checking EPS creep under sustained load

Polystyrene and thermal insulation

In brief

Polystyrene under constant load can deform over time. This phenomenon is called creep. It is not described by the CS(10) value alone, which relates to a short-term compression test. For design purposes, CC data or other relevant manufacturer data are needed. The distribution of pressures and the permissible settlement of the entire system must also be assessed. When a force is applied, the material initially deforms. If the load continues to act, the thickness can change over time even without any increase in force. It is precisely this part of the behaviour that matters beneath permanent layers, shelving, supports or structures. A short load test on site does not show the entire multi-year process.

White polystyrene board and a metal flat bar lying next to it on a table

How does creep differ from initial deflection?

The assessment concerns not only strength in the sense of sudden failure. Even slight settlement can affect the floor, the roof pitch or the connection to the adjacent element. It is also important whether the deformations are uniform. Two parts of a floor loaded differently may displace in different ways. The design therefore needs both the level of pressure and a serviceability criterion.

Why is CS(10) not a serviceability limit?

CS(10) describes the compressive stress at 10% relative deformation in the relevant test. For a board 100 mm thick, such deformation corresponds to 10 mm. Usually this is not a movement that can simply be permitted beneath a finished floor. The CS(10) value must therefore not be converted into a weight and the result regarded as a permissible load over many years.

Likewise, automatically adopting one per cent of CS(10) for all boards is too great a simplification. Conditions and data specific to the product are needed. The compression parameter helps to distinguish between grades, but it does not replace a full assessment. If the manufacturer states a service load, it must be checked to what period, deformation and reference system this information relates.

How do you read the CC designation?

The CC designation combines deformation levels, time and stress. The example CC(2/1.5/50)50 means a limitation of the total reduction in thickness to 2% and of the creep-related part to 1.5% for a period of 50 years, at a stress of 50 kPa, under the conditions of the adopted test and extrapolation. The order of the numbers matters. The final 50 is neither a number of years nor a percentage.

Such a designation appears in the documentation for specific products, but it must not be attributed to every EPS board. Long-term data are determined in accordance with the test method and the rules for predicting behaviour over time. This does not mean that every sample lay in the laboratory for half a century. In the design, the scope of the data and their applicability to actual conditions must be checked.

How does thickness affect the magnitude of displacement?

The same percentage of deformation means a different change in dimension at different thicknesses. Two per cent of 100 mm is 2 mm, and of 200 mm it is 4 mm. The percentage alone therefore does not show the full effect on the floor level or the support of equipment. In a system with several layers, their combined behaviour must be assessed. The result of only one of the boards must not be attributed to the entire assembly.

The layers that distribute the pressure also matter. A rigid, correctly designed screed can change the load area on the insulation. However, this does not mean arbitrary distribution of force over the entire floor area of the room. Supports, movement joints and edges are particularly important. The design should determine how the load actually reaches the EPS, instead of dividing the total weight by the entire floor area.

What data should be passed to the designer?

The weight of the permanent layers and equipment, the imposed loads and the dimensions of the supports are required. The screed build-up, the EPS thickness and the expected service life must be specified. Temperature and moisture conditions are important if they affect the application. The designer determines the appropriate combinations and permissible deformations. Only on this basis can a specific board be assessed.

If NPD appears in the declaration for a given characteristic, this means that the property is not determined in that document. It is not zero creep, nor automatic proof of suitability. Additional technical data from the manufacturer may be needed. Where the design requires verification, it should not be replaced by a comparison of density or by pressing the board with one’s hand. Such observations do not describe behaviour over time.

What should be checked after selecting the material?

On site, the specified support and board layout must be ensured. Voids, steps and accidental cuts can cause local deformation regardless of correctly selected parameters. Temporary storage of materials is also important. A large stack of bags on a small section of floor can load the insulation differently from the intended end use. The works programme should take such situations into account.

EPS is produced by, among others, Swisspor, Arsanit, Genderka and Paneltech. For loaded applications, data should be sought for the specific grade, not the general brand. After a change in equipment or manner of use, the loads must be checked again. Correct creep selection combines the material documentation with the expected behaviour of the entire floor, roof or foundation.

7 branches. Materials closer to your project.

Izoprofil.eu map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote

Materials for your project