Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Why a ground-bearing floor needs a different thermal calculation from a wall

Polystyrene and thermal insulation

At a glance

A ground floor releases heat to a medium that behaves differently from outdoor air. What matters is not only the EPS and concrete layers but also the building geometry, the perimeter and the properties of the ground. That is why simply inverting the sum of the resistances does not describe the whole issue. An assessment requires a method suited to contact with the ground. In a simple wall model, heat passes through successive layers to the air on the other side. Under a building it also spreads sideways in the ground. The path at the perimeter differs from the path under the centre of an extensive floor. This phenomenon is spatial. A mere list of the thicknesses of concrete, EPS and screed does not describe its full geometry.

White polystyrene next to a concrete sample and a container of aggregate, illustration of floor layers

Where does the heat flow path run?

The ground also has thermal capacity and responds to temperature changes at a different rate than the air. The conditions beneath a building do not change in exactly the same way as the temperature read on an outdoor thermometer. The calculations use appropriate assumptions regarding the climate and the properties of the substrate. The lower surface of the floor should not be treated like a wall exposed directly to frost.

Is the formula R = d/λ still useful?

Yes, the thermal resistance of the EPS layer can still be determined from its thickness and lambda. For example, 15 cm at λ = 0.035 gives R of approximately 4.29 m²K/W. This is valuable information about the insulation itself. It is not yet the U-value of the floor on the ground. The proper method uses the resistances of the layers together with geometric data and the characteristics of the ground.

It is easy to make a mistake here when comparing offers. A seller may correctly state the R of the board, and the investor may treat its reciprocal as the finished result for the whole floor. Yet the insulation has a specific function within a larger system. The R of two materials helps compare their thermal contribution. However, further data are needed to assess the building element and the building’s losses.

Why do the area and the perimeter change the result?

Let us consider two floors with an area of 100 m². A square of 10 × 10 m has a perimeter of 40 m. A rectangle of 5 × 20 m has a perimeter of 50 m. With the same area, the second shape has a greater perimeter. If the other conditions are comparable, the difference in geometry affects the heat flow through the ground. One cannot assign both cases a result based solely on the EPS thickness.

For the calculations, the perimeter and area must be adopted in accordance with the rules of the given method. Not every internal wall increases the perimeter interacting with the surroundings. Ground levels, the depth of embedment and the proximity of other spaces also matter. A simplified plan should reflect the actual building. In the case of a complex building form, a single equivalent rectangle may be too great a simplification.

What does edge insulation achieve?

The junction of the floor, foundation wall and façade requires thermal continuity. A break at this point can increase losses and lower the local surface temperature. Adding EPS only in the middle of the floor does not automatically solve the edge problem. The vertical insulation of the foundation, the course of the wall and the floor level relative to the ground must be taken into account.

Various perimeter insulation solutions may appear in the design. Their effect depends on position, dimensions and geometry. There is no single strip width that gives the same result in every house. The thermal bridge at the junction of wall and floor requires a separate assessment. Care must be taken not to count the same part of the heat flow twice in the ground model and the junction balance.

What data can a wall calculator not replace?

The assessment requires the floor layers, the area, the correct perimeter and data on the ground. The arrangement of the insulation, the depth and the way it is used are significant. A floor directly on the ground is considered differently from a ceiling above an unheated basement. Entering all these situations as an ordinary wall in the calculator can give a seemingly precise but incorrect result.

With underfloor heating, the downward heat flow under operating conditions of the installation must also be considered. It is not limited to the difference between the room air temperature and the outside temperature. The requirements for the heating system and the energy assessment of the building serve different functions. It is good when the floor design and the installation design use the same set of data and layers.

How do you choose EPS after the thermal calculation?

The selected thickness must fit within the assembly and meet the mechanical requirements. Loads, support and creep under constant pressure are checked. CS(10) is not a permissible service load. If the board comes into contact with moisture, the correct grade and a suitable protective assembly are required. EPS does not replace waterproofing or the preparation of a load-bearing substrate.

The EPS manufacturers are Genderka, Arsanit, Enerpor and Paneltech. Their boards should be selected according to specific data, not just the underfloor label. A correct design combines the thermal result with the structure, water conditions and the perimeter detail. This ensures that the number describing thermal insulation refers to the actual floor, not to a simplified wall turned horizontal.

7 branches. Materials closer to your project.

Izoprofil.eu map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote